spsemi features for surface mounted applications in order to optimize board space pb-free plated peak power is 720w@1ms esd rating of class x (> 15 kv) (iec6100-4-2) response time is typically<1 ns low profile package typical i less than 1a above 10v r low inductance excellent clamping capability aec-q101 tsc(720w) series applications i/o interface ac/dc power supply low frequency signal transmission line (rs232, rs485, etc.) mechanical characteristics case: jedec do-214aa. molded plastic over glass passivated junction solderable per mil-std-750, method 2026 terminal: color band denoted positive end (cathode) except bidirectional polarity: 12mm tape (eia std rs-481) standard packaging: 0.003 ounce, 0.093 gram weight: maximum ratings and characteristics ratings at 25 ambient temperature unless otherwise specified. notes : 1.non-repetitive current pulse , per fig. 3 and derated above ta = 25 per fig. 2 . 2.mounted on 5.0mm x 5.0mm (0.03mm thick) copper pads to each terminal 3.8.3ms single half sine-wave , or equivalent square wave, duty cycle = 4 pulses per minutes maximum. peak pulse power dissipation on 10/1000s waveform peak forward surge current,8.3ms single half sine-wave superimposed on rated load,(jedec method) (note2,3) operating junction and storage temperature range rating symbol value units p ppm i fsm t,t jstg minimum 720 - 55 to +150 100 watts amps functional diagram bi-directional uni-directional cathode anode www.spsemi.cn page 1 of 5 rev 2017 .. 03 01 .
spsemi www.spsemi.cn page 2 of 5 dimensions (do-214aa) tsc(720w) series electrical characteristics tsc6.0u tsc8.0u tsc12u tsc15u tsc16u tsc18u tsc20u tsc22u tsc26u tsc28u TSC30U tsc33u tsc36u tsc40u tsc58u tsc60u tsc150u tsc170u tsc440u tsc part number device marking code reverse stand-off voltage v (v) rwm v (v)min. br v (v)max. br te s t current it(ma) maximum clamping voltage @ipp vc(v) peak pulse current ipp(a) reverse leakage @v rwm i( a) r uni-polar uni bi-polar bi kg kr le lm lp lt lv lx me mg mk mm mp mr ng nk pm pr qm ag ar be bm bp bt bv bx ce cg ck cm cp cr dg dk em er fm 6.0 8.0 12.0 15.0 16.0 18.0 20.0 22.0 26.0 28.0 30.0 33.0 36.0 40.0 58.0 60.0 150.0 170.0 440.0 6.67 8.89 13.30 16.70 17.80 20.00 22.20 24.40 28.90 31.10 33.30 36.70 40.00 44.40 64.40 66.70 167.00 189.00 492.00 7.37 9.83 14.70 18.50 19.70 22.10 24.50 26.90 31.90 34.40 36.80 40.60 44.20 49.10 71.20 73.70 185.00 209.00 5 43.00 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10.3 13.6 19.9 24.4 26.0 29.2 32.4 35.5 42.1 45.4 48.4 53.3 58.1 64.5 93.6 96.8 243.0 275.0 713.0 70.0 52.9 36.2 29.5 27.7 24.7 22.2 20.3 17.0 15.9 14.9 13.5 12.4 11.2 7.7 7.4 3.0 2.6 1.0 100 50 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 breakdown voltage @i t tsc6.0b tsc8.0b tsc12b tsc15b tsc16b tsc18b tsc20b tsc22b tsc26b tsc28b tsc30b tsc33b tsc36b tsc40b tsc58b tsc60b tsc150b tsc170b tsc440b for bidirectional type having v of 10 volts and less, the i limit is double. wrm r 0.086 2.20 () 0.073 1.85 () 0.180(4.57) 0.160(4.06) 0.155(3.94) 0.130(3.30) cathode band do-214aa(smb j-bend) dimensions in inches and(millimeters) 0.098(2.50) 0.083(2.10) 0.220 5.59 () 0.205 5.21 () 0.012 0.305 () 0.006 0.152 () 0.060 1.52 () 0.030 0.76 () 0.012(0.3)max. rev 2017 .. 03 01 .
spsemi www.spsemi.cn page 3 of 5 tsc(720w) series ratings and characteristic curves(ta=25 unless otherwise noted) fig.1 peak pulse power rating fig.2 pulse derating cruve i-v curve characteristics uni-directional bi-directional i pp i r i t v c v b r v rwm i pp i r i t v c v br v rwm v i pp i r i t v c v br v rwm v f v fig.3 pulse waveform fig.4 typical junction capacitance 0 0 1.0 2.0 4.0 3.0 10/1000 sec waveform . as defined by r.e.a half value i ppm 2 tr=10us peak value i ppm t=25 j pulse width(td) is defined ad the point where the peak current decays to 50% of i ppm 50 100 150 i -peak pulse current(%) ppm t-time(ms) td 0255075 100 125 150 175 200 0 25 50 75 100 t -ambient temperature( ) a peak pulse power(p ) or current(i ) pp ppm derating in percentage,% 0.2 0.2"(5.0 5.0mm) copper pad areas c -junction capacitance(pf) j 1 10 100 10 100 1000 10000 v -reverse stand-off voltage(v) wm v ,measured at r stand-off voltage,v wm 200 tj=25 f=1.0mh z vsig=50mvp-p measured at zero bias uni-directional bi-directional p -peak pulse power (kw) ppm 0.1 s 10 s 10ms 0.1 10 100 td - pulse width (sec.) 1 1.0 s 100 s 1.0ms non-repetitive pulse waveform shown in fig.3 ta = 25c rev 2017 .. 03 01 .
spsemi www.spsemi.cn page 4 of 5 tsc(720w) series ratings and characteristic curves fig.5 typ.transient thermal impedance fig.6 maximum non-repetitive peak forward surge current uni-directional only recommended soldering conditions recommended conditions reflow soldering t s t p t l time 25 time to peak temperature (t 25 to peak) temperature t (min) s t (max) s t l t p preheat ramp-down ramp-up critical zone ttot lp re?ow condition pb-free assembly (see fig.1) pre heat -temperature min(t ) s(min) -temperature max(t ) s(max) -time(min to max)(t ) s average ramp up rate (liquidus temp(t ) to peak) l t to t -ramp-up rate s(max) l re?ow -temperature(t )(liquidus) l -temperature(t ) l peak temp(t ) p time within 5 of actual peak temp(t ) p ramp-down rate time 25 to peak temp(t ) p do not exceed +150 +200 60-180secs 3 /sec.max. 3 /sec.max. +217 60-150secs +260(+0/-5) 30 secs.max. 6 /sec.max. 8 min.max. +260 0.001 0.1 0.1 1 1000 10 1.0 10 100 transient thermal impedance(c/w) tp-pulse duration(sec) 0.01 100 marking code cathode band kg **** marking code logo date code ag **** marking code logo date code peak forward surge current(a) 1 10 10 100 100 200 number of cycles at 60h z 8.3ms single half sine-wave (jedec method) unidirectional only rev 2017 .. 03 01 .
spsemi www.spsemi.cn page 5 of 5 tsc(720w) series packing options and reel specification-do-214aa 0.157 (4.0) 0.47 (12.0) 0.157 (8.0) 0.49 (12.4) symbol ea per reel reel dia (mm) industry standard tsc*** 3000 330 eia rs-481 13.0(330) rev 2017 .. 03 01 .
|
